Hello Everyone,
I made a mistake on an ISO i built for someone at another location.
I can't get back to that location to run the wizard again.
I simply need to add a few entries to the whitelist.
Is it possible to do this after the fact?
Where is the whitelist located in the file structure?
I appreciate any help or direction.
All the best,
Nick
Editing the whitelist after iso is built
Forum rules
Porteus Kiosk section of the forum is unmaintained now. Its kept in a 'read only' mode for archival purposes.
Please use the kiosk contact page for directing your queries: https://porteus-kiosk.org/contact.html
Porteus Kiosk section of the forum is unmaintained now. Its kept in a 'read only' mode for archival purposes.
Please use the kiosk contact page for directing your queries: https://porteus-kiosk.org/contact.html
-
fanthom
- Moderator Team
- Posts: 5667
- Joined: 28 Dec 2010, 02:42
- Distribution: Porteus Kiosk
- Location: Poland
- Contact:
Re: Editing the whitelist after iso is built
Hello Nick,
Whitelist is included in the kiosk config which is encrypted and embedded in the kiosk ISO. For security reasons is not possible to update the config manually (unless remote management option is enabled). If you give me ssh access and your fixed kiosk config then I could reburn the ISO remotely.
Please send these details on [email protected] if you are interested. Support fees will apply.
Whitelist is included in the kiosk config which is encrypted and embedded in the kiosk ISO. For security reasons is not possible to update the config manually (unless remote management option is enabled). If you give me ssh access and your fixed kiosk config then I could reburn the ISO remotely.
Please send these details on [email protected] if you are interested. Support fees will apply.
Please add [Solved] to your thread title if the solution was found.
Re: Editing the whitelist after iso is built
I have a iso that i have built and need to add a few entry's to the whitelist
can i unpack the ISO myself , modify the whitelist / config and then repack it?
sorry if this seams like a repeat of the question above, however i wasn't sure if the reason he can not do it is because he does not have the device / ISO with him.
can i unpack the ISO myself , modify the whitelist / config and then repack it?
sorry if this seams like a repeat of the question above, however i wasn't sure if the reason he can not do it is because he does not have the device / ISO with him.
-
tome
- Contributor
- Posts: 686
- Joined: 26 Jun 2013, 14:03
- Distribution: x64 Openbox
- Location: Russia is causing the immense damage to humanity
- Contact:
Re: Editing the whitelist after iso is built
Yes.can i unpack the ISO myself , modify the whitelist / config and then repack it?
EDIT:
Sorry, the answer is NO
-
fanthom
- Moderator Team
- Posts: 5667
- Joined: 28 Dec 2010, 02:42
- Distribution: Porteus Kiosk
- Location: Poland
- Contact:
Re: Editing the whitelist after iso is built
This is actually not possible:
http://porteus-kiosk.org/faq.html#3
http://porteus-kiosk.org/faq.html#3
Please add [Solved] to your thread title if the solution was found.
Re: Editing the whitelist after iso is built
Thanks
when it is encrypted in the OS does it end up in the setting.xzm file?
reason i ask is that i have unziped the settings file and made changes to firefox (after the setup wizard has been run)
can i simply run the setup wizard on a fresh version of Kiosk.iso (to make white list changes) then unpack the new iso, replace the settings file with my old settings file and then remake the iso?
when it is encrypted in the OS does it end up in the setting.xzm file?
reason i ask is that i have unziped the settings file and made changes to firefox (after the setup wizard has been run)
can i simply run the setup wizard on a fresh version of Kiosk.iso (to make white list changes) then unpack the new iso, replace the settings file with my old settings file and then remake the iso?
